Two quirks with new trim install

Reply

  #1  
Old 05-14-17, 05:42 PM
I
Member
Thread Starter
Join Date: Apr 2016
Location: USA
Posts: 35
Received 0 Votes on 0 Posts
Two quirks with new trim install

I'm installing new trim throughout much of our first floor and I've got two installation areas where I'm looking for advice on the best look. For reference, here's a couple photos of our base treatment, which is a combination of 5 1/4" base, a 5 3/4" tall by 1 1/4" plinth, and shoe (sorry for the askew photos):

Name:  File_000.jpg
Views: 175
Size:  18.7 KB



Name:  File_002.jpg
Views: 156
Size:  21.4 KB

My first question has to do with how best I should terminate my shoe into what I guess would be called the stringer of my stairs. Although my base will terminate no problem, my shoe will stick out a bit. Should I return miter this (90? 22 1/2?) at the stringer and be done, or run this shoe continuously all the way around the stringer and newel post (with several outside corner miters and inside corner copes), or something else? Here's a few pics of the situation (the last pic is from the opposite end viewing the post and stringer):

Name:  File_004.jpg
Views: 164
Size:  23.6 KB


Name:  File_005.jpg
Views: 156
Size:  24.6 KB


Name:  File_006.jpg
Views: 178
Size:  22.0 KB

Second, I have a closet where I've already installed the plinth blocks and nothing else. I know that one wall in my closet is too close to the entry, and so when I install the base and shoe these will run to a certain extent into the face of the plinth unless I do something differently. Granted, this is a closet so it's not mission critical, but is there an ideal way to handle close quarters like this so that things look as good as possible? I can remove or do whatever I need to with the plinth if that would help.

Thanks!
 

Last edited by chandler; 05-14-17 at 06:00 PM.
  #2  
Old 05-14-17, 06:04 PM
chandler's Avatar
Banned. Rule And/Or Policy Violation
Join Date: Dec 2005
Location: USA
Posts: 39,965
Received 6 Votes on 6 Posts
Cut your shoe at a 30 degree angle to where it dies directly on the vertical. If your molding is 3/4" and the vertical is 1", then cut your shoe with a 1/4" square edge at the end of the base and angle it back from that point at 30 degrees.

For your closet without base, just trim it in shoe and let it die into the plinth block. IMO adding base would make it too bulky looking.
 
  #3  
Old 05-14-17, 06:10 PM
XSleeper's Avatar
Group Moderator
Join Date: Dec 2004
Location: USA
Posts: 26,531
Received 779 Votes on 718 Posts
Shoe either gets butted, returned or bobbed at a 45, depending on the situation.
 
  #4  
Old 05-22-17, 12:43 PM
G
Member
Join Date: Jul 2014
Location: usa
Posts: 232
Received 0 Votes on 0 Posts
I agree terminate the show at the bottom of the stairs with a 30 or 45 degree cut and don't continue the shoe to wrap around all the existing moulding at the end of the stairs.

------------------------

I think I know what you mean about the closet - the wall which holds the door is only about 3" long of a wall on the inside of the closet, so when you add the plinth on the inside, then the wall that meets that 3" wall will have moulding that runs into the face of the plinth. ?

I would either leave the plinth out or run the moulding (base and 1/4 round) into the face of the plinth. I wouldn't cut the plinth to be narrower to prevent the other wall's mounding from terminating into the face of the plinth.
Personally yes I would install the plinth and terminate the joined wall's moulding into the face of the plinth.
 
 

Thread Tools
Search this Thread
 
Ask a Question
Question Title:
Description:
Your question will be posted in: