Looking for socket with just the right length and depth
#1
Looking for socket with just the right length and depth
I want to replace the coolant temperature sensor on my truck. When I replaced it years ago, the only tool I could fit in there was a 12-point combination wrench. And even then, it took me over an hour to replace it because you can only make very small movements with the wrench in the tight working quarters.
Deep socket, crowsfoot wrench, and ratchet wrench won't work either in the tight space.
If I can find a socket that isn't to shallow or too deep, I think that will work. The socket needs to
accommodate a 2-1/4 inch sensor. I already looked in all the stores and a few websites.
Do any of you know where I can get a 1 Inch diameter (for 1/2 inch drive) socket with just the right depth?
Deep socket, crowsfoot wrench, and ratchet wrench won't work either in the tight space.
If I can find a socket that isn't to shallow or too deep, I think that will work. The socket needs to
accommodate a 2-1/4 inch sensor. I already looked in all the stores and a few websites.
Do any of you know where I can get a 1 Inch diameter (for 1/2 inch drive) socket with just the right depth?
#2
Group Moderator
Buy a 1" socket and cut it down to the height you need. There are more than a few "customized" tools in my shop.
#3
That's not a bad idea. It had crossed my mind too. But I don't have a power saw. And I wouldn't attempt to hacksaw through it. Where can I get it cut down?
#4
Member
Buy a 4.5 inch grinder ($10) and a package of 4.5 inch metal cutoff wheels ($6) from HF and do it yourself.
#5
Group Moderator
#7
I looked at the Harbor Freight website. You really can get a grinder for $14.99. Probably wouldn't last long for heavy use. But enough to get the job done.
What about just using my power drill with a cutting wheel?
What about just using my power drill with a cutting wheel?
#9
Group Moderator
Your drill won't work. You need the high rpm of the grinder for cutting metal. Putting a cutting wheel in a drill is more like sanding your way through. You could do it but it will test your patience.
#12
Member
Join Date: Mar 2006
Location: Wet side of Washington state.
Posts: 16,321
Received 38 Upvotes
on
30 Posts
Buy the very thin metal-cutting discs that fit the grinder. The clerks at Harbor Freight are usually quite helpful.
Be sure to hold the grinder tightly and not twist the wheel in the cut or it will break. I suggest a full face shield when doing the cutting.
Be sure to hold the grinder tightly and not twist the wheel in the cut or it will break. I suggest a full face shield when doing the cutting.
#13
At the Harbor Freight look for "thin metal cut-off discs". They are 3/64" thick so wear face protection as Furd suggests, and consider hearing protection too.
There will be a tendency for your cut to drift- these grinders require a steady hand, and it may take a couple tries to get it right (HF sells individual sockets so a spare or two may be in order). The disc is a consummable: as you cut it will get smaller and create a cloud of carborundum dust. You'll also create a stream of sparks, so be aware of what is down range (such as flammable items or fluid). The hot sparks will embed themselves into certain surfaces, too, ask me how i know. Paint and glass will be damaged.
On the bright side, get a coupon from the HF website for 20% price reduction and another for a "free" flashlight. Cool!
There will be a tendency for your cut to drift- these grinders require a steady hand, and it may take a couple tries to get it right (HF sells individual sockets so a spare or two may be in order). The disc is a consummable: as you cut it will get smaller and create a cloud of carborundum dust. You'll also create a stream of sparks, so be aware of what is down range (such as flammable items or fluid). The hot sparks will embed themselves into certain surfaces, too, ask me how i know. Paint and glass will be damaged.
On the bright side, get a coupon from the HF website for 20% price reduction and another for a "free" flashlight. Cool!
#15
Group Moderator
When cutting off the socket be mindful of where your sparks are going. It will send a fine dust of metal across the room (dirty). More important though when cutting you'll see bright yellow hot metal spraying off which can start a fire if you are not careful.
#18
I was overlooking something all this time.
A 1 inch socket with a 3/8 drive takes up less space. So I purchased these items this morning: 1 inch socket, 3/8 inch drive, and swiveling universal joints. I should have added these to my toolbox years ago. I also disconnected the upper radiator hose and a vacuum hose to open up more space to work in.
This made it a lot easier to remove and install a new sensor without cutting down a socket.
But I couldn't pass up a $15 grinder. So I picked up one at Harbor Freight. I can already think of a couple projects I'll need it for early next year. I printed your advice on grinder use. So you guys have already helped me for something in the future. Done. Thanks again.
A 1 inch socket with a 3/8 drive takes up less space. So I purchased these items this morning: 1 inch socket, 3/8 inch drive, and swiveling universal joints. I should have added these to my toolbox years ago. I also disconnected the upper radiator hose and a vacuum hose to open up more space to work in.
This made it a lot easier to remove and install a new sensor without cutting down a socket.
But I couldn't pass up a $15 grinder. So I picked up one at Harbor Freight. I can already think of a couple projects I'll need it for early next year. I printed your advice on grinder use. So you guys have already helped me for something in the future. Done. Thanks again.
#19
Along the same lines, I found this idea recently on one of the 3D printer forums. It was only for the 1/4 drive but I expanded to add 3/8 and 1/2 drive. Great for staring a nut or bolt where you can't fit a ratchet in a confined space.