DoItYourself.com Community Forums > Interior Improvement Center > Patching and Plastering

Archway Tearaway L Bead

Thread Tools

Search this Thread

01-09-19, 08:34 AM

mossman

Member

Thread Starter

Join Date: Mar 2009

Location: Northern Virginia

Posts: 3,913

Upvotes: 5

Received 25 Upvotes on 20 Posts

Archway Tearaway L Bead

The big box stores in my area don't carry archway tearaway L bead, nor can I find limited quantities online for purchase. Is it possible to make an archway bead out of a regular L bead by clipping the flange in several areas?

Upvote

01-09-19, 09:08 AM

marksr

Forum Topic Moderator

Join Date: Mar 2005

Location: USA - N.E.Tn

Posts: 45,500

Upvotes: 613

Received 800 Upvotes on 703 Posts

I would think it would be difficult to maintain a fluid bend. Have you checked with a drywall supply house?

Upvote

01-09-19, 10:32 AM

mossman

Member

Thread Starter

Join Date: Mar 2009

Location: Northern Virginia

Posts: 3,913

Upvotes: 5

Received 25 Upvotes on 20 Posts

Apparently a nearby supply house is a Trimtex distributor. I'll call them.

Upvote

01-09-19, 01:00 PM

tightcoat

Member

Join Date: Jul 2003

Location: California

Posts: 1,914

Upvotes: 10

Received 44 Upvotes on 37 Posts

IF YOU CHOOSE to make your own the key to a smooth bend is to space the slots evenly the whole length. Don't make one space 1" and another 1 1/2".

Upvote

Thread Tools

Search this Thread

Show Printable Version

Email this Page

Patching and Plastering
Tiling over a brick fireplace mantle

B

biederboat on Jan 07, 2019

I hope this is the right subforum to put this in, I couldn't find one that covered tiling. We have a brick fireplace mantle in a downstairs (daylight basement, dirt side) family room. The brick is 90% "clean and dry" but there is one small section that has "powdered" due to some light moisture. This has affected both the brick and the mortar. We haven't used this much so I really can't tell if it was a something that happened over time or relatively quickly. I'd like to tile over the entire mantle and wondering if I might run into trouble with this issue. At the very least I'd clean it up well, maybe using muriatic acid? Looking for any suggestions to hopefully keep the tile intact. Thanks, BBRead More
Patching and Plastering
Advice needed with patching sheet rock in ceiling

D

David_Helms on Jan 23, 2019

My house is a 50 year old two story home built with textured dry wall ceilings and copper pipe. My upstairs bathroom is directly above the kitchen, and I developed a pin-hole leak in a pipe, which caused a wet spot in the corner of my kitchen. I had a plumber come in and replace the copper pipe from where it came up the first floor all the way to the sink and bathtub. This required the plumber cut out about a 10 ft long x 3 ft wide piece of sheet rock to replace all of the copper all the way to the sink. When removing the sheet rock, he cut the sheet rock by following a beam running the length of the kitchen. To put up new sheet rock, he screwed a 2x3 strip to the existing roof beam to secure the sheet rock to. He then had another guy come in and texture the ceiling. The problem was the new texture didn't match the original texture, and it's very obvious. I've been removing the popcorn from my ceilings for a couple of years, so I decided to remove the texture from the ceiling. After scraping the texture, I didn't like what I saw. The plumber cut the sheet rock parallel to a wood beam, but the original piece of sheet rock ended on the same stud. After removing the texture, I have a thin strip of sheet rock about 3/4" wide (the remnant of the piece he cut out) between the old and new sheet rock. The plumber also didn't do the best job of cutting the old sheet rock. The area he cut out must have been out of square because there were gaps up to about 3/8" wide at opposite ends of the new piece he installed. He just filled that with mud and used a standard piece of tape. That leaves very little tape extending beyond the two seams. I also noticed the original sheet rock is harder than the new sheet rock mud. I need to re-tape this joint and would like some thoughts on how best to repair this. Here are my questions: 1. I found 6" adhesive fiberglass tape for sale. I've used fiberglass tape to repair small holes but never to tape a seam. I haven't seen any wide paper tape. Would you recommend using the 6" wide fiberglass tape along the seam? What about putting down the fiberglass tape first, then applying paper tape over that? I know it will be a little high at the seam, but I think I could make the seam wide enough to hide the added thickness. Can you use fiberglass tape alone, no paper tape? 2. I noted there was a definite difference in the hardness of the new and old sheet rock. I tried using a wet sponge to remove the sheet rock on the original joint without much luck, so I'm guessing I will sand it off. I've already pulled off the original tape and the new tape. I have an oscillating tool with a sander head, so I was going to use that to remove excess mud on the original sheet rock if I can do so without damaging the original sheet rock. Is there a better way to remove the original mud? I was planning to put a thin layer of new sheet rock over both joints before applying new tape. 3. I talked about using fiberglass tape with adhesive backing, but I don't think that will adhere very well to sanded sheet rock. Would it be a good idea to put a coat of primer over the sheet rock before applying the new tape and mud? This repair is directly over top of the sink and counter top in the kitchen. I'd like to fix it permanently so I don't have to deal with repairing cracks down the road. I'd appreciate any advice you guys can offer. BTW, I've done a fair amount of drywall repairs and have re-taped a couple of seams in walls, but I've never tried to re-tape a mixture of new and old sheet rock.Read More

Ask a Question