Energy Efficient Windows

Windows bring light, warmth, and beauty into buildings and give a feeling of openness and space to living areas. They can also be major sources of heat loss in the winter and heat gain in the summer. In 1990 alone, the energy used to offset unwanted heat losses and gains through windows in residential and commercial buildings cost the United States $20 billion (one-fourth of all the energy used for space heating and cooling). However, when properly selected and installed, windows can help minimize a home's heating, cooling, and lighting costs. This article elaborates on all the available options of windows for improving a home's heating and cooling energy requirements.

Controlling Air Leaks

When air leaks around windows, energy is wasted. Energy is also transferred through the centers, edges, and frames of windows. Eliminating or reducing these paths of heat flow can greatly improve the energy efficiency of windows and, ultimately, of homes. Several options are available to reduce air leaks around windows; the least expensive options are caulking and weatherstripping, but could very well end up in the replacement of windows.

Caulking and Weatherstripping

Caulks are compounds (usually latex or silicone) used to fill cracks and holes. Before applying new caulk, old caulk or paint residue remaining around a window should be removed using a putty knife, stiff brush, or special solvent. After the old caulk is removed and the surfaces cleaned, the new caulk can then be applied to all joints in the window frame and the joint between the frame and the wall. The best time to apply caulk is during dry weather when the outdoor temperature is above 45° Fahrenheit (7.2° Celsius). Low humidity is important during application to prevent cracks from swelling with moisture. Warm temperatures are also necessary so the caulk will set properly and adhere to the surface.

Weatherstripping is a narrow piece of metal, vinyl, rubber, felt, or foam that seals the contact area between the fixed and movable sections of a window joint. It should be applied between the sash and the frame, but should not interfere with the operation of the window.

Window Construction

The construction and quality of the window usually affect a window's air infiltration and heat loss characteristics. Windows are available in many different constructions with varying degrees of energy efficiency. Some of the more common window types are fixed-pane, casement, double- and single-hung, horizontal sliding, hopper, and awning windows.

When properly installed, fixed-pane windows are airtight and inexpensive and can be custom designed for a wide variety of applications. But, because they cannot be opened, fixed-pane windows are much better suited where you have to air-condition, but not so in places where ventilation is required.

Casement, awning, and hopper windows with compression seals are moderately airtight and provide good ventilation when opened. Casement windows open sideways with hand cranks. Awning windows are similar to casement windows except that their hinges are located at the tops of the windows instead of at the sides. Hopper windows are inverted versions of awning windows with their hinges located at the bottom, awning windows being outswing while hopper windows are best-suited inswing so rain doesn't come in. Windows with compression seals are much more energy-efficient than double-hung and horizontal sliding windows which need a much more flexible and softer seal between the frame and the sliding parts.

Double-hung windows have top and bottom sashes (the sliding sections of the window) and can be opened by pulling up the lower sashes or pulling down the upper sash. Although they are among the most popular type of windows, double-hung windows can be less inefficient because they are prone to air leaks. Single-hung windows are somewhat better because only one sash moves. Horizontal sliding windows are like double-hung windows except that the sashes are located on the left and right edges rather than on the tops and bottoms. Horizontal sliding windows open on the side and are especially suitable for spaces that require a long, narrow view. These windows, however, usually provide minimal ventilation and can be more difficult to seal from air leaks.

Reducing Heat Loss and Condensation

Manufacturers usually represent the energy efficiency of windows in terms of their U-values (conductance of heat) or their R-values (resistance to heat flow). If a window's R-value is high, it will lose less heat than one with a lower R-value. Conversely, if a window's U-value is low, it will lose less heat than one with a higher U-value. In other words, U-values are the reciprocals of R-values (U-value = 1/R-value). Most window manufacturers use R-values in rating their windows.

Usually, window R-values range from 0.9 to 3.0 (U-values range from 1.1 to 0.3), but some highly energy-efficient exceptions also exist. When comparing different windows, you should ensure that all U-or R-values listed by manufacturers: (1) are based on current standards set by the American Society of Heating, Refrigeration, and Air-Conditioning Engineers (ASHRAE), (2) are calculated for the entire window, including the frame, and not just for the center of the glass.

The following five factors affect the R-value of a window.

1. The type of glazing material (e.g., glass, plastic, treated glass)

2. The number of layers of glass

3. The amount of air gap between the layers of glass

4. The thermal resistance or conductance of the frame and spacer materials

5. The last factor depends mostly on the efficiency of its installation when it gets sealed around the frame opening (i.e., air leaks - see the previous discussion).

Types of Glazing Materials

Traditionally, clear glass has been the primary material available for window panes in homes. However, in recent years, the market for glazing - or cutting and fitting window panes into frames - has changed significantly. Now several types of special glazings are available that can help control heat loss and condensation.

Low-Emissivity (Low-E) Glass

Has a special surface coating to reduce heat transfer back through the window. These coatings reflect from 40 to 70 percent of the heat that is normally transmitted through the clear glass while allowing the full amount of light to pass through.

Heat-Absorbing Glass

Contains special tints that allow it to absorb as much as 45 percent of the incoming solar energy, reducing heat gain. Some of the absorbed heat, however, passes through the window by conduction and reradiation.

Reflective Glass

Has been coated with a reflective film and is useful in controlling solar heat gain during the summer. It also reduces the passage of light all year long, and, like heat-absorbing glass, it reduces solar transmittance.

Plastic Glazing Materials

Acrylic, polycarbonate, polyester, polyvinyl fluoride, and polyethylene are also widely available. Plastics can be stronger, lighter, cheaper, and easier to cut than glass. Some plastics also have higher solar transmittance than glass. However, plastics tend to be less durable and more susceptible to the effects of weather than is glass.

Storm Windows

Can increase the efficiency of single-pane windows, the least energy-efficient type of glazing. The simplest type of storm window is a plastic film taped to the inside of the window frame. These films are usually available in prepackaged kits. Although plastic films are easily installed and removed, they are easily damaged and may reduce visibility. Rigid or semirigid plastic sheets such as plexiglass, acrylic, polycarbonate, or fiber-reinforced polyester can be fastened directly to the window frame or mounted in channels around the frame usually on the outside of the building. These more durable materials are also available in kits.

Layers of Glass and Air Gaps

Standard single-pane glass has very little insulating value (approximately R-1). It provides only a thin barrier to the outside and can account for considerable heat loss and gain. Traditionally, the approach to improve a window's energy efficiency has been to add layers of glass while keeping a pre-determined air gap between each pane, as each layer of air space is an added insulation to the glass surface. Double- or triple-pane windows have insulating air- or gas-filled spaces between each pane.

Each layer of glass and the air spaces resist heat flow. The amount of gap of air space between the panes is important because if the gaps are too wide (more than 5/8 inch or 1.6 centimeters) or too narrow (less than 1/2 inch or 1.3 centimeters) it lowers the R-values (i.e., they allow too much heat transfer). Advanced, multi-pane windows are now manufactured with inert gases (argon or krypton) in the spaces between the panes because these gases transfer less heat than does air.

Multi-pane windows are considerably more expensive than single-pane windows and limit framing options because of their increased weight but also their thickness.

Frame and Spacer Materials

Window frames are available in a variety of materials including aluminum, wood, vinyl, and fiberglass. Frames may be primarily composed of one material, or they may be a combination of different materials such as wood clad with vinyl or aluminum-clad wood. Each frame material has its advantages and disadvantages.

Aluminum frames - Conduct heat and therefore lose heat faster and are prone to condensation. Through anodizing or coating, the corrosion and electro-galvanic deterioration of aluminum frames can be avoided. Additionally, the thermal resistance of aluminum frames can be significantly improved by placing continuous insulating plastic strips or a bridge between the interior and the exterior of the frame.

Wood frames - Have higher R-values, are not affected by temperature extremes, and do not generally promote condensation. Wood frames do require considerable maintenance in the form of periodic painting or staining. If not properly protected, wood frames can swell, which leads to rot, warping, and leading to major deterioration of the wood components and malfunctions.

Vinyl window frames - Which are made primarily from polyvinyl chloride (PVC), offer many advantages. Available in a wide range of styles and shapes, vinyl frames have moderate to high R-values, are easily customized, are competitively priced, and require very low maintenance. While vinyl frames do not possess the inherent strength of metal or wood, larger-sized windows are often strengthened with aluminum or galvanized steel reinforcing profiles.

Fiberglass frames - Fiberglass frames are relatively new and are not yet widely available. With some of the highest R-values, fiberglass frames are excellent for insulating and will not warp, shrink, swell, rot, or corrode. Unprotected fiberglass does not hold up to the weather and therefore is always specially treated. Some fiberglass frames are hollow; while others are filled with fiberglass insulation.

Spacers

Spacers are used to separate multiple panes of glass within the windows to create an insulating gap between each pane. Although metal (usually aluminum) spacers are commonly installed to separate glass in multi-pane windows, they conduct heat. During cold weather, the thermal resistance around the edge of a window is lower than that in the center; thus, heat can escape, and condensation can occur along the edges. To alleviate these problems, one manufacturer has developed a multi-pane window using a 1/8-inch-wide (0.32 centimeters-wide) PVC foam separator placed along the edges of the frame. Like other multi-pane windows, these use metal spacers for support, but because the foam separator is secured on top of the spacer between the panes, heat loss and condensation are greatly reduced. Several window manufacturers now sandwich foam separators, nylon spacers, and insulation materials such as polystyrene and Rockwool between the glass inside their windows.

Additional Options for Reducing Heat Loss and Gain through Windows

Movable insulation, such as insulating shades, shutters, and drapes, can be applied on the inside of windows to reduce heat loss in the winter and heat gain in the summer. Shading devices, such as awnings, exterior shutters, or screens, can be used to reduce unwanted heat gain in the summer.

In most cases, these window treatments are more cost-effective than energy-efficient window replacements and should be considered first.

Conclusion

Reducing heat loss or gain in homes often includes either improving existing windows or replacing them. Low-cost options available for improvement are caulking, weatherstripping, retrofit window films, and window treatments. Replacing windows will involve the purchase of new materials, which should adhere to certain energy efficiency standards.

Different combinations of window style, frame material, and glazing can yield very different results when weighing energy efficiency and cost. For example, a fixed-pane window is the most air-tight and the least expensive; a window with a wood frame is likely to have less conductive heat loss than one with an aluminum frame; double-pane, a lighter Low-E window may be just as efficient as triple-pane untreated windows, but at a much lower cost.

No one window is suitable for every application. Many types of windows and window films are available that serve different purposes. Moreover, you may discover that you need two types of windows for your home because of the directions that your windows face and your local climate. To make wise purchases, first, examine your heating and cooling needs and prioritize desired features such as daylighting, solar heating, shading, ventilation, and aesthetic value.